AP Calculus AB and BC
Volumes with Known Cross Sections: Setup and Examples
To find the volume of a solid with known cross sections, write the area A(x) of one slice in terms of x and integrate A(x) across the base. The slice's side length s comes from the base region, usually top curve minus bottom curve. Squares have area s^2, semicircles (pi/8)s^2, and equilateral triangles (sqrt(3)/4)s^2.
One formula for every shape
Picture a flat region in the -plane as the base of a solid. Thin slices stand upright on the base, each one perpendicular to an axis, and every slice has the same kind of shape: a square, a rectangle, a triangle, or a semicircle. The volume is the integral of the slice area. These solids are covered in Topic 8.7, Volumes with Cross Sections: Squares and Rectangles, and Topic 8.8, Volumes with Cross Sections: Triangles and Semicircles.
Here is the area of the cross section at position , and and are the -values where the base begins and ends. Each thin slice has volume close to , area times thickness, and the integral adds the slices. Nothing in this formula changes from shape to shape. The only work is writing .
Get the side length from the base
Each slice sits on a line segment that stretches across the base. Call the length of that segment . For slices perpendicular to the -axis, the segment is vertical, so its length is the top curve minus the bottom curve:
For slices perpendicular to the -axis, the segment is horizontal. Solve each boundary curve for in terms of , take as the right curve minus the left curve, and integrate with respect to between the lowest and highest -values of the base.
| Slices perpendicular to | Segment across the base | Side length | Integrate with respect to |
|---|---|---|---|
| the -axis | vertical | top minus bottom, in terms of | |
| the -axis | horizontal | right minus left, in terms of |
This is the same length you would integrate to find the area of the base. For a cross-section volume, that length goes into an area formula first.
Area formulas in terms of s
Once is known, the slice area is a geometry formula. Read the problem carefully for which part of the shape lies in the base.
| Cross section | How it sits on the base | Area |
|---|---|---|
| Square | one side in the base | |
| Rectangle with given height | base side in the base | |
| Semicircle | diameter in the base | |
| Equilateral triangle | one side in the base | |
| Isosceles right triangle | a leg in the base | |
| Isosceles right triangle | the hypotenuse in the base |
Two of these deserve a derivation, since they are the ones most often written wrong. A semicircle with diameter has radius , so its area is . An isosceles right triangle with hypotenuse has legs of length , so its area is .
A rectangle's height may be a constant, such as , or may depend on the base side, such as a height equal to twice the base, which gives area .
How this relates to disks and washers
The disk method is this same formula with a circular slice. When a region is revolved around an axis, each cross section perpendicular to that axis is a circle of radius , so and . A washer is a circle with a circular hole, with area .
The difference is in how the solid is described. A solid of revolution comes from spinning a region, and the slices are circles automatically. A known cross-section solid is not spun. The problem tells you the base and the slice shape, and no appears unless the slices are semicircles or other circular pieces. The known cross-sections vs solids of revolution page compares the two setups.
Common mistakes
- Integrating the side length and stopping. That gives the area of the base. The integrand has to be the slice area.
- Squaring the two curves separately. For squares the area is , which is different from . The second expression belongs to washers.
- Using as the radius of a semicircle. The segment across the base is the diameter, so the radius is .
- Putting in front of a square or triangle cross section out of habit from the disk method.
- Integrating with respect to when the slices are perpendicular to the -axis.
- Using the wrong bounds. The bounds are where the base region starts and ends along the axis the slices are perpendicular to.
Quick check
Constant factors can be pulled out front. Semicircles on a base give exactly times the volume that squares on the same base would give, and equilateral triangles give times it. If you have already computed one, the others follow by multiplying.
Worked examples
Worked example
Square cross sections
The base of a solid is the region bounded by , the -axis, and the line . Cross sections perpendicular to the -axis are squares. Find the volume.
- Find the side length. The slices are perpendicular to the -axis, so is top minus bottom: .
- Write the area of a square slice: .
- Set the bounds. The base runs from to .
- Integrate: .
cubic units
Worked example
Semicircular cross sections
The base of a solid is the region bounded by and the -axis. Cross sections perpendicular to the -axis are semicircles with their diameters in the base. Find the volume.
- Find the bounds. The parabola meets the -axis where , at and .
- Find the diameter: .
- Write the area of a semicircular slice: .
- Integrate the polynomial. The integrand is even, so .
- Multiply by the constant: .
cubic units
Worked example
Rectangles perpendicular to the y-axis
The base of a solid is the region bounded by and the line . Cross sections perpendicular to the -axis are rectangles of height . Find the volume.
- The slices are perpendicular to the -axis, so work in terms of . Solve for : the right boundary is and the left boundary is .
- Find the side length as right minus left: .
- Write the area of a rectangular slice with height : .
- Set the bounds. The base runs from the vertex at up to the line .
- Integrate: .
cubic units
Frequently asked questions
How is a cross-section volume different from the disk method?
The setup is the same integral of slice area. In the disk method the solid comes from revolving a region, so every slice is a circle with area . With known cross sections the solid is not revolved, and the problem states the slice shape, so the area formula is for a square, rectangle, triangle, or semicircle.
How do I know whether to integrate with respect to x or y?
Use the axis the slices are perpendicular to. Cross sections perpendicular to the -axis mean and . Cross sections perpendicular to the -axis mean and , with the boundary curves rewritten as functions of .
Why is the semicircle area ?
The segment across the base is the diameter, so the radius is . A full circle with that radius has area , and half of that is .